Builds

1-19-13 NTM Prop Drive Series 28-26A 1200kv / 250w BUILDS!

quadcopter X666 KK2 1.5 1.8 kg 4x 2200 3s frame Hobbyking X666 Glass Fiber Quadcopter Frame 666mm www.hobbyking.com board Hobbyking KK2.0 Multi-rotor LCD Flight Control Board www.hobbyking.com motors NTM Prop Drive Series 28-26A 1200kv / 250w www.hobbyking.com ESC - flashed at home by me with SimonK firmware HobbyKing 30A BlueSeries Brushless Speed Controller www.hobbyking.com props Carbon Fiber 10x4.5" CW CCW Counter Rotating Propellers www.rctimer.com Batt 2x2 parralel Turnigy nano-tech 2200mah 3S 25~50C Lipo Pack www.hobbyking.com


Assembling a Hoverthings.com HT-FPV frame with

DJI Naza-M + GPS Flight Controller
Spektrum AR8100 Receiver
NTM Prop Drive Series 28-26A 1200kv Motors
TURNIGY Plush 25amp Speed Controllers
Hobbyking Distribution Board


ESC reflashed with SimonK firmware

RCTimer Carbon Fiber 10x4.5" CW CCW Counter Rotating Propellers

SIX Glass Fiber Hexcopter Frame 600mm

frame
SIX Glass Fiber Hexcopter Frame 600mm
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=26514&aff=448825

board
Hobbyking KK2.0 Multi-rotor LCD Flight Control Board
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=24723&aff=448825

motors
NTM Prop Drive Series 28-26A 1200kv / 250w
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=17345&aff=448825

ESC
HobbyKing 30A BlueSeries Brushless Speed Controller
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=13429&aff=448825

Batt
Turnigy nano-tech 2200mah 3S 25~50C Lipo Pack
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=11911&aff=448825


FPV BANDIT

This quad is perfect for FPV! It flies very stable so it's also capable for some aerial photography (except for the fact that it can only carry a gopro and not something like a Sony NEX-5). At the end of the video there's also some flight footage. Hope you guys like it!

Parts:

HT-FPV frame:
http://www.hoverthings.com/frame-sets/htfpvblack.html

Multirotor circuit board:
http://www.hoverthings.com/accessories/power-distribution-board.html

DJI naza multirotor controller:
http://www.hoverthings.com/accessories/djinaza.html

NTM Prop Drive Series 28-26A 1200kv / 250w:
http://www.hobbyking.com/hobbyking/store/__25084__NTM_Prop_Drive_Series_28_26A_1200kv_250w_short_shaft_version_.html

TURNIGY Plush 30amp Speed Controller:
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=2164

Turnigy nano-tech 3300mah 3S 45~90C Lipo Pack
http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=11953



Home made Quadcopter
From 15mm PVC Pipe and "T" Adapters.
DJI Naza flight controller
Gaui 8x4.5" Props
NTM Prop Drive Series 28-26A 1200kv (from hobbyking.com)
Advance 20A ESC
FPV Gear from (rangevideo.com)
Build Forum:
http://www.multirotorforums.com/showthread.php?2993-Matts-PVC-T-QUAD


ESC reflashed with SimonK firmware RCTimer Carbon Fiber 10x4.5" CW CCW Counter Rotating Propellers SIX Glass Fiber Hexcopter Frame 600mm frame SIX Glass Fiber Hexcopter Frame 600mm www.hobbyking.com board Hobbyking KK2.0 Multi-rotor LCD Flight Control Board www.hobbyking.com motors NTM Prop Drive Series 28-26A 1200kv / 250w www.hobbyking.com ESC HobbyKing 30A BlueSeries Brushless Speed Controller www.hobbyking.com Batt Turnigy nano-tech 2200mah 3S 25~50C Lipo Pack www.hobbyking.com


Getting there.. HT-FPV Frame HT-FPV Power Distribution Board NTM Prop Drive Series 28-26A 1200kv / 250w DJI ESC-30A OPTO Brushless Speed Controller DJI NAZA Multi-Rotor Stabilization Controller with GPS Add-on GAUI 210801 8-inch Prop Set (8A and 8B) Turnigy nano-tech 3300mah 3S 45~90C Lipo Futaba T8FG Super 14ch Transmitter w/R6208SB 2.4GHz Receiver 1.2Ghz Low Pass Filter 1.3Ghz Tuned to 1280Mhz 14dBi Panel Antenna 1.3 GHz Bluebeam Whip Antenna Set SMA Right Angle Adapter Fat Shark Dominator Modular Design 640x480 FPV Video Glasses Racewood 1.3GHz 500mW Wireless AV Transmitter Blue Label Racewood 1.3GHz Wireless AV Receiver VRx Blue Label BEVRC PV700 FPV Camera - 600TVL SONY SUPER HAD CCD D-WDR Color Board Camera DNR Camera - GoPro Hero2


Flying FPV (First Person View) means that you put a small camera on the front of your vehicle which transmits the video image to a screen or video goggles. You have a feeling of sitting in the "cockpit" and can go much further than regular RC flying (you're not limited to your eyes). Setup: Quadcopter: Transmitter Turnigy 9x (with frsky DIY module) Turnigy 3000mAh 3s 30c NTM Prop Drive Series 28-26A 1200kv / 250w TURNIGY Plush 25amp Speed Controller Hobbyking x525 frame Hobbyking KK2.0 Multi-rotor LCD props: apc 8x3.8 FPV setup (First Person View): Fatshark dominators Video TX:immersion rc 5.8ghz Video RX:5.8 ghz uno receiver (immersion rc) Immersion rc spironet video tx/rx cloverleafs Eagle tree OSD, GPS, Logger Turnigy 600tvl camera Video TX battery: zippy 800mAh 2s 15c AUW: (including batteries, cameras...): 1499 gr Flight time is around 7-8 minutes This was filmed with the RD32II action camera (no stabilisation program) More video's coming so subscribe!


SIX-6

KK2 parameters. frame SIX Glass Fiber Hexcopter Frame 600mm www.hobbyking.com board Hobbyking KK2.0 Multi-rotor LCD Flight Control Board www.hobbyking.com motors NTM Prop Drive Series 28-26A 1200kv / 250w www.hobbyking.com ESC reflashed with SimonK firmware HobbyKing 30A BlueSeries Brushless Speed Controller www.hobbyking.com Batt Turnigy nano-tech 2200mah 3S 25~50C Lipo Pack www.hobbyking.com RCTimer Carbon Fiber 10x4.5" CW CCW Counter Rotating Propellers


1st. Line Of Sight Flight Frame made from PVC 1/2 inch Wyes (Y) adapters. PVC 1/2 inch pipe for the arms. Using:KK2 Flight Controller: Motor:Turnigy NTM 28-26 1200kv ESC: Turnigy Plush 25 amp. Battery: Zippy Flightmax 3s 5000mah 20c Total Flight Weight (no payload): 2433grams. Flight time approx 9 minutes. Build Forum. www.multirotorforums.com



Sent from my iPad